Announcement

Collapse
No announcement yet.

modern receiver hitch and M37

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Doc Dave
    replied
    To answer one of your questions, I too thought that ideally the "drop" of the hitch would be somewhat less; the receiver would be only say 2" below the pintle. As it is, it's not "bad" unless you were doing rock crawling maybe.
    If one could find a receiver hitch off the shelf that has a little less drop, then it might be perfect.

    To fab different hitch flanges with less drop (and correct strength, etc) is above my pay grade!

    Leave a comment:


  • Doc Dave
    replied
    86F55D56-726C-47D9-8F7D-4FF32FD9D0E4.jpg

    Leave a comment:


  • Doc Dave
    replied
    3548D754-8220-4E08-BC2D-1CCAC52622F0.jpg

    Leave a comment:


  • Doc Dave
    replied
    6351D8FF-4FD1-4467-9B59-25162E2B6C53.jpg

    Leave a comment:


  • Doc Dave
    replied
    726E7056-F9A3-4E48-9B58-DEB08DE5A6C5.jpg

    Leave a comment:


  • Doc Dave
    replied
    0A635868-3629-47ED-8E03-4FB833B7A8CE.jpg

    Leave a comment:


  • Doc Dave
    replied
    Addendum/clarification to my post:
    I forgot to say that for the rear-most bolt to attach the hitch to the frame flanges, I removed the stock rivets that attached the rear crossmember to the frame flanges and then put a 1/2" grade 8 bolt through that on each side.
    To help drill the other holes in the frame, using the holes in the hitch flanges as a general guide, I used big C clamp- type vice grips to hold the hitch up to the frame ear so as to allow me to mark centers on the frame flanges with a center punch.
    Then, I used a "poor mans magnetic drill" to make drilling up from under the vehicle much easier. I put a small towel around the rear handle of the 1/2" drill, and placed this in a vertical position under the truck frame; the handle fit in the saddle of a floor jack. Once aligned, I gradually pumped the handle and drilled the holes much easier! I learned this trick from a local mechanic.
    The back surface of the receiver hitch, when looking at things from the side, is maybe 1/2-1" forward of where the end of the pintle is, if you put a plumb straightedge down from the end of the pintle.
    The pictures that follows should help with understanding the fitment.

    Leave a comment:


  • Doc Dave
    replied
    After my original post in 2011, I had a lot of "life happens" situations going on. I only recently went back to the M37.

    Among other things I got the gas tank Renu'd and installed, and fabricated the fuel and return line fittings to this.

    I'm happy to say the stock Dodge 3/4 ton pickup receiver hitch from my 2001 Ram fit the M37 perfectly!
    i was able to use the existing holes in the hitch flange as a guide to drill 1/2" holes in the lower frame ears. I used grade 8 bolts to attach the frame and the results are very nice.
    i did not have to grind or modify anything.

    I blasted the hitch in my media blaster cabinet and then painted it black.

    Leave a comment:


  • John Mc
    replied
    Doc Dave - still hoping to see some pictures of your installation sometime.

    I've got to make the decision on what I'm going to do with my installation. I misread your original description, and thought you had mounted the hitch on the rear cross-member. Mounting to the frame seems like a better way to go, and being a bolt-on installation makes for easy removal if I need to do gas-tank work in the future.

    Some photos I'd love to see:
    • Where the receiver ended up in relation to your bumper (height below your rear cross-member and/or pintle hitch, as well as how far the receiver sticks out behind the rear cross-member.)
    • Underside of the truck showing mounting to the frame
    • I'm especially interested in where the bolt holes from the hitch fell on your frame. In talking to etrailer, they say that the distance between frame rails is standard among most full-size trucks. What differs is where the bolt holes are and how much "drop" they build in from the frame on the truck to the hitch's cross bar in order to get the receiver to come out under a modern truck's bumper. It appears that I only need minimal drop to clear things on the M37, so there might be other options that out make for a tighter fit than the stock 2001 Dodge hitch fit.
    • Anything else you think would be helpful as I try to make my decision. I'm considering buying a new aftermarket hitch for a Dodge full-size pickup, so anything you can show me where I might need to be concerned about the fit as I consider the various aftermarket models would be appreciated
    I'm also interested in your comments on how it has been working out for you. What kind of loads have you towed, and have you had any issues with your installation?

    I've found some really good options for powering 12V trailer lights and 12V trailer brakes for my M37, so the only thing remaining is to figure out the mechanical installation.

    Leave a comment:


  • Doc Dave
    replied
    After my original post in 2011, I had a lot of "life happens" situations going on. I only recently went back to the M37.

    Among other things I got the gas tank Renu'd and installed, and fabricated the fuel and return line fittings to this.

    I'm happy to say the stock Dodge 3/4 ton pickup receiver hitch from my 2001 Ram fit the M37 perfectly!
    i was able to use the existing holes in the hitch flange as a guide to drill 1/2" holes in the lower frame ears. I used grade 8 bolts to attach the frame and the results are very nice.
    i did not have to grind or modify anything.

    I blasted the hitch in my media blaster cabinet and then painted it black.

    Leave a comment:


  • John Mc
    replied
    Doc Dave - I'm wondering what ever came of this project. I'm just getting started on my M37, and trying to figure out how I might add a receiver hitch.

    Leave a comment:


  • Doc Dave
    replied
    Hi Jared,
    I will try to get some pics soon...I got the frame and axles done but then the project has been on hold and I haven't finished the hitch.

    Leave a comment:


  • jrodjared
    replied
    Wow great! Any pics of the install? Does the stock hitch have the tabs face outward or inward? I mean does the hitch mount in-between the frame rails or on the outside?

    Leave a comment:


  • Doc Dave
    started a topic modern receiver hitch and M37

    modern receiver hitch and M37

    I have a '52 M37. Now that I have finally finished my civvie PW resto, I am going to start on the M37 this winter.
    My M37 is going to look stock on the outside but have some upgrades in the power train, seats and brakes.
    Last month I removed a stock class 3 receiver hitch from my 2001 Ram and replaced it with a class 5. I thought this old hitch would be just extra iron laying around unless I could sell it locally.
    Last week I was doing a little measuring and inspecting, and just for curiosity sake took the receiver hitch over and held it up to the frame rails of the M37. It looks like it will drop right in with just a very small amount of grinding of the edge of its ears in a few places! The receiver opening will be below the pintle, so I can keep that. How often does that happen- with this many years and design differences? Maybe Murphy is not always on duty!
Working...
X